User Tools

Site Tools


This is an old revision of the document!

Mapping from NSW Lidar

NSW Spatial Services have undertaken a program to map all of NSW using lidar (light detecting and ranging) For details, see information on their elevation program.

Elevation data can best be accessed through the Geoscience Australia ELVIS program.

It can then processed with a GIS such as QGIS to create useful topographic maps. Instructions below are specifically for use with QGIS, though the general outline may be useful for other GISs.


The original topics here are being progressively moved to their own pages

Managing DEMs

  • Merging DEMs - how to merge DEMs in QGIS
  • Managing large DEMs - while data can be downloaded in an ad hoc manner, if you are regularly processing NSW DEMs, it is better to have the DEM tiles already downloaded. This page provides steps to do this in an automated manner.

Topographic maps

There are several primary data items for topographic maps that can be generated using the DEM data from the NSW Lidar.

  • Hydrologically correct DEM - prior to further operations, it is usually important to make sure that your DEM is free of depressions. Otherwise these will mess up streams and possibly contours.

Once you have a depressionless DEM, the following items can be generated:

Topographic maps

There are several primary data items for topographic maps that can be generated using the DEM data from the NSW Lidar. The main ones are:

  • Contours
  • Hydrology (Stream Network)
  • Clifflines

The steps below are works in progress to determine effective (the best?) ways to extract the various items out of the DEM data for use in topographic maps. Any feedback/suggestions of improvements are welcome.


The steps below are being developed for use in the Blue Mountains, a region that has a significant number of relatively vertical sandstone cliffs. It may be less effective in different terrain.

This is more a set of ideas than a fully fledged process. The main aims are to get a set of steps that can largely be automated, and that create cliffline vectors that are running in the correct direction. There is still some way to go on this!

Initial analysis of slope, aspect

SAGA → Terrain Analysis - Morphometry → Slope, Aspect, Curvature


Slope, Aspect 

using DEM and [1] Maximum Triangle Slope (Tarboton (1997)). I haven't tested any other algorithms.

Cliff areas can be identified using a range of say 60-90 and 70-90 degrees on the Slope file. Using 60-90 degrees helps connect logical cliffs and avoid small breaks.

Initial Cleaning

Next convert data to 1 bit (1,2 not 0,1, as Sieve ignores 0s) using Raster Calculator. Formula is: (Slope > 60) + 1

Then Sieve resulting data using a Threshold of 100 and 8-connectedness to get rid of small non-connected cliffs. Note above that Sieve doesn't like 0s.

Also good to rerun Sieve with smaller Threshold (1-10) and 4-connectedness to a) get rid of some small dangles. b) fill small holes.

Additional smoothing can be done using a User Defined Filter with the following matrix. This will apply some smoothing by allowing you to reclassify the pixel values, and remove single pixel indentations like this:

000    000
101 -> 111
111    111

and single pixel protrusions like this:

000    000
010 -> 000
111    111

The main problem is that the matrix has to be defined each time in QGIS. There doesn't seem to be an option to load it. Possibly this can be done outside QGIS.

Matrix is:

0.0 0.5 0.0
0.5 0.5 0.5
0.0 0.5 0.0

If the original matrix is 0/1 then the cutoff will be 1.5

If the original matrix is 1/2 then the cutoff will be 3.5

This step could be run multiple times - some testing would need to be done to determine how many times.

Other options for cleaning the data include a plugin called LecoS, but this doesn't work on QGIS 3. Another possibility is Shrink and Expand - radius 1? But this also creates some new holes that didn't previously exist, so not ideal.


Convert back to 0/1 data using Raster Calculator

Use Translate: set Output Data Type = Byte, set NoData = 0

Run r.thin - r.thin is quite picky about the input file format. Needs to be NULL/non-NULL (not float or int). The Translate process above provides this. The previous two steps could be combined into one. Also, this file may need to be explicitly saved (not just a temporary file?!)


Run set Feature Type = line

Run v.clean: Cleaning Tool = rmdangle, Threshold = 5,10

Dumping Ground / WIP



The below snip of Breakfast Creek makes use of TPI calculated from a LIDAR derived DEM. Only positive values for TPI as displayed, which indicate cliff-like features. It is then combined with contours and aerial imagery to convey the terrain of the area.

TPI from LIDAR DEM combined with contours and imagery to show clifflines and terrain

nsw_lidar.1613556919.txt.gz · Last modified: 2021/02/17 21:15 by bushwalking

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki